Tag: wifi

Content

//----------------------------------------------------------------//
//    Temps-i 7 WiFi clock and temperature in 4 digit display     //
//  v 1.0.1                                                       //
//                                                                //
//  Interfaces:                                                   //
//  - Sparkfun ESP32-Thing micocontroller                         //
//  - BMP-280 temperature and pressure digital sensor             //
//  - 4 digit 7 segment display                                   //
//  - Programm push button                                        //
//  - LiPo Battery                                                //
//                                                                //
//  Detailed documentation:                                       //
//  https://theroamingworkshop.cloud                              //
//                                                                //
//                © THE ROAMING WORKSHOP 2022                     //
//----------------------------------------------------------------//
#include < esp_wifi.h >
#include < WiFi.h >
#include < WiFiMulti.h >
#include "time.h"
#include "sntp.h"
#include < Wire.h >
#include < Adafruit_BMP280.h >
// Spaces inside <> only shown for correct html display. Remove them in Arduino IDE
//BMP280 sensor using I2C interface
Adafruit_BMP280 bmp;
#define BMP_SCK  (4)
#define BMP_MISO (21)
#define BMP_MOSI (4)
#define BMP_CS   (21)
//Sensor variables
float TEMP=0;     //temperature variable
float ALT=0;      //altitude variable
float PRES=0;     //pressure variable
float hREF=1020.0;//sea level reference pressure in hPa
//define time variables
RTC_DATA_ATTR long long TIME=0; //concatenated time
RTC_DATA_ATTR long long d=0;  //day
RTC_DATA_ATTR long long m=0;  //month
RTC_DATA_ATTR long long Y=0;  //year
RTC_DATA_ATTR long long H=0;  //hour
RTC_DATA_ATTR long long M=0;  //minute
RTC_DATA_ATTR long long S=0;  //second
RTC_DATA_ATTR uint32_t dS=0;  //seconds counter for dot
RTC_DATA_ATTR struct tm timeinfo; //saves full date variable
long long inicio=0; //saves start time
long long ahora=0;  //saves current time
//Define digit pins in an array, in display order, for looping
//Numbers match ESP32-Thing GPIO number
int DigPins[4]{
  17,// first digit (GPIO 17)
  23,//second digit (GPIO 23)
  19,//third digit  (GPIO 19)
  25//fourth digit  (GPIO  25)
};
//Define segment pins
//Numbers match ESP32-Thing GPIO number
int SegPins[8]{
  14,   //P
  26,   //g
  18,   //f
  13,   //e
  12,   //d
  27,   //c
  22,   //b
  15    //a
};
//Auxiliary variables
//Numbers match ESP32-Thing GPIO number
int ProgPin=32;   //Pin no used for program
int ButtonStatus=1;
int ledPin=5;     //Used to blink the ESP32-Thing blue led
int ProgNum=-1;   //Define a variable to keep track of current program number
// WIFI
// Define your wifi network and credentials
char ssid1[] = "YOUR_WIFI_SSID1";
char pass1[] = "YOUR_WIFI_PASS1";
char ssid1[] = "YOUR_WIFI_SSID2";
char pass1[] = "YOUR_WIFI_PASS2";
WiFiMulti wifiMulti;
// NTP variables
// Update time zone if needed
const char* ntpServer1 = "pool.ntp.org";
const char* ntpServer2 = "time.nist.gov";
const long  gmtOffset_sec = 3600;
const int   daylightOffset_sec = 0; //this will be corrected later with software
const char* time_zone = "CET-1CEST,M3.5.0,M10.5.0/3";  // TimeZone rule for Europe/Rome including daylight adjustment rules (optional)
// Displayed characters in every digit are a byte array indicating ON (1) and OFF (0) segments
// Use a wiring pattern that matches an understandable byte chain so you can make them up easily
// Segment/byte pattern: Babcdefgp --> where 1 is HIGH (ON) and 0 is LOW (OFF)
// Refer to a character by calling this array, i.e.:
//  - call number 3 by calling ns[3]
//  - call letter A by calling ns[20]
//  - call underscore symbol (_) by calling ns[49]
byte ns[50]{ // Array Position - Byte character
  B11111100,// 0-0
  B01100000,// 1-1
  B11011010,// 2-2
  B11110010,// 3-3
  B01100110,// 4-4
  B10110110,// 5-5
  B10111110,// 6-6
  B11100000,// 7-7
  B11111110,// 8-8
  B11110110,// 9-9
  B11111101,// 10-0.
  B01100001,// 11-1.
  B11011011,// 12-2.
  B11110011,// 13-3.
  B01100111,// 14-4.
  B10110111,// 15-5.
  B10111111,// 16-6.
  B11100001,// 17-7.
  B11111111,// 18-8.
  B11110111,// 19-9.
  B11101110,// 20-A
  B00111110,// 21-b
  B10011100,// 22-C
  B01111010,// 23-d
  B10011110,// 24-e
  B10001110,// 25-f
  B10111100,// 26-G
  B00101110,// 27-h
  B00001100,// 28-I
  B11111000,// 29-J
  B01101110,// 30-K(H)
  B00011100,// 31-L
  B00101010,// 32-m(n)
  B00101010,// 33-n
  B00111010,// 34-o
  B11001110,// 35-P
  B11100110,// 36-q
  B00001010,// 37-r
  B10110110,// 38-S
  B00011110,// 39-t
  B01111100,// 40-U
  B00111000,// 41-v
  B00111000,// 42-w(v)
  B01101110,// 43-X(H)
  B01110110,// 44-y
  B11011010,// 45-Z
  B00000001,// 46-. (dot)
  B11000110,// 47-* (astherisc)
  B00000010,// 48-- (hyphon)
  B00010000,// 49-_ (underscore)
};
//array to store displayed digits
int digits[4];
//digit calculation variables
int first_digit = 0;
int second_digit = 0;
int third_digit = 0;
int fourth_digit = 0;
//counters for looping digits and current number
int dig=0;
int n=0;
int dot=1;
void setup()
{
  // Start disabling bluetooth and WIFI to save energy
  // Just power WIFI later, when needed.
  esp_err_t esp_bluedroid_disable(void);
  esp_err_t esp_bt_controller_disable(void);
  WiFi.disconnect(true);
  WiFi.mode(WIFI_OFF);
  
  // Start serial communication for any debug messages
  // Commented for production; uncomment for debugging
  //Serial.begin(115200);
  //Define I2C pins, as we are not using standard ones
  Wire.begin(21,4);
  // Activate digit pins looping the pin array.
  for (dig=0; dig<4; dig++){
    pinMode(DigPins[dig], OUTPUT);
  }
  for (dig=0; dig<4; dig++){  //set them LOW (turn them OFF)
    digitalWrite(DigPins[dig], LOW);
  }
  // Activate segment pins
  for (int i=0; i<8; i++){
    pinMode(SegPins[i],OUTPUT);
  }
  // Activate LED pin
  pinMode(ledPin, OUTPUT);
  // Activate PROG pin
  pinMode(ProgPin, INPUT_PULLUP);
  // Turn ON Wifi
  wifiON();
  
  // Setup NTP parameters
  sntp_set_time_sync_notification_cb( timeavailable );
  sntp_servermode_dhcp(1);
  configTime(gmtOffset_sec, daylightOffset_sec, ntpServer1, ntpServer2);
  //wait for date
  do{
    delay(100);
  }while(TIME==0);
  delay(500);
  //WIFI can be turned off now
  wifiOFF();  
  // Setup BMP280
  unsigned status;
  //BMP-280 I2C Address:
  // 0x76 if SD0 is grounded
  // 0x77 if SD0 is high
  status = bmp.begin(0x76);
  if (!status) {
    Serial.println(F("Could not find a valid BMP280 sensor, check wiring or "
                      "try a different address!"));
    Serial.print("SensorID was: 0x"); Serial.println(bmp.sensorID(),16);
    Serial.print("        ID of 0xFF probably means a bad address, a BMP 180 or BMP 085\n");
    Serial.print("   ID of 0x56-0x58 represents a BMP 280,\n");
    Serial.print("        ID of 0x60 represents a BME 280.\n");
    Serial.print("        ID of 0x61 represents a BME 680.\n");
    ESP.restart();
    while (1) delay(10);
  }
  //Default settings from datasheet.
  bmp.setSampling(Adafruit_BMP280::MODE_NORMAL,     // Operating Mode.
                  Adafruit_BMP280::SAMPLING_X2,     // Temp. oversampling
                  Adafruit_BMP280::SAMPLING_X16,    // Pressure oversampling
                  Adafruit_BMP280::FILTER_X16,      // Filtering.
                  Adafruit_BMP280::STANDBY_MS_500); // Standby time.
  //get initial readings
  readSensors();
  
  // Get correct time
  sync_clock();
  num_shift();
  // Set start time
  inicio = millis();
  // Set dot time
  dS=millis();
}
void loop(){
  // After setup, this function will loop until shutdown.
  
  // Start time counter using chip's milisecond counter
  uint32_t ahora=millis();
  
  // Check if the counter has reached 60000 miliseconds.
  // Calibrate if you realize that time desyncs
  // This depends on processor calculation, which can vary with input voltage (if on batteries) and temperature.
  while ( (ahora-inicio+(S*1000)) < 59500){
    // Run dot blinker when not showing temperature
    //commented as it sometimes desyncs the hour digit (needs fixing)
    /*if(ProgNum==-1){
      dot_blinker();
    }*/
    
    // Reading push button:
    // when pressed change status
    if(digitalRead(ProgPin)==1){
      ButtonStatus=1;
    }
    // when released after press, set "program change" status
    // this avoids constant change when holding
    if(digitalRead(ProgPin)==0 && ButtonStatus==1){
      ButtonStatus=2;
    }
    // Status 2 -> Programm change
    if(ButtonStatus==2){
      //reset status
      ButtonStatus=0;
      //update programm number
      ProgNum=-ProgNum;
      Serial.println(ProgNum);
      //change to temp
      if(ProgNum==1){
       //light LED
       digitalWrite(ledPin, HIGH); 
       //save TIME
       TIME=digits[0]*1000+(digits[1]-10)*100+digits[2]*10+digits[3];
       //show temp
       room_temp();
      }else if(ProgNum==-1){  //change to time
        //turn off LED
        digitalWrite(ledPin, LOW);
        //restore time
        split_time(TIME);
      }
    }
    
    //update time counter
    ahora=millis();
    num_shift();
    delay(6);
  }
  // End of while() after 60 seconds
  // Reset initial time
  S=0;
  inicio=millis();
  //make sure there's dot at the end
  if(digits[1]<=10){
    digits[1]+10;
    dot=0;
  }
  //update time
  //if program is in temperature, change to time
  if(ProgNum==1){
    split_time(TIME);
    ProgNum=-1;
  }
  updateMinutes();
}
//-WIFI function
//--Setup and turn Wifi ON
void wifiON(){
  // Set up WIFI (ESP32 Thing only working with wifiMulti library)
  Serial.println("Conectando");
  wifiMulti.addAP(ssid1,pass1);
  //wifiMulti.addAP(ssid2,pass2);
  int led=1;
  int boot=1;
  wifiMulti.run();
  //WiFi.disconnect(true);
  
  while((WiFi.status() != WL_CONNECTED)){
    digitalWrite(ledPin, HIGH);
    delay(500);
    digitalWrite(ledPin,LOW);
    delay(500);
    wifiMulti.run();
  }
  // Make sure LED is off when finished
  digitalWrite(ledPin,LOW);
  // When CONNECTED, while loop ends.
  Serial.print("Conectado a ");
  Serial.println(WiFi.SSID());
  Serial.println(WiFi.localIP());
}
//-Disable WIFI
void wifiOFF(){
  //turn WIFI off as it's not needed any more
  WiFi.disconnect(true);
  WiFi.mode(WIFI_OFF);
  //disable wifi (deinit clears all flash data)
  esp_wifi_deinit();
}
//----BMP280 functions
//-Read sensor data
void readSensors(){
  TEMP=bmp.readTemperature();
  Serial.println("T: "+(String)TEMP+"ºC");
  PRES=bmp.readPressure();
  Serial.println("P: "+(String)PRES+"hPa");
  ALT=bmp.readAltitude(hREF);
  Serial.println("h: "+(String)ALT+"msnm");
}
//----NTP functions
//-Callback function (get's called when time adjusts via NTP)
void timeavailable(struct timeval *t)
{
  Serial.println("Got time adjustment from NTP!");
  simpleTime();
}
void simpleTime()
{ 
  if(!getLocalTime(&timeinfo)){
    Serial.println("No time available (yet)");
    return;
  }
  Serial.print("Synced time: ");
  Serial.println(&timeinfo, "%A, %B %d %Y %H:%M:%S");
  //save time
  sync_clock();
}
//-
//PROGRAM #0: HELLO at startup
//function to say "HOLA" at start up while connecting to WiFi
void ini_HOLA(){
  int h=30;
  int o=34;
  int l=31;
  int a=20;
  digits[0]=46;
  digits[1]=46;
  digits[2]=46;
  digits[3]=46;
}
//PROGRAM #1: WiFi synced time
//function that gets current time via WiFi
void sync_clock(){
  Y=timeinfo.tm_year;
    TIME=TIME+Y*10000000000;
  m=timeinfo.tm_mon;
  m=m+1;
    TIME=TIME+m*100000000;
  d=timeinfo.tm_mday;
    TIME=d*1000000;
  H=timeinfo.tm_hour;
  //check daylight saving time and correct hour
  //"27 Mar (03 27) +1 hour; 30 Oct (10 30) back -1 hour"
  if( ( m*100+d >= 327 ) && ( m*100+d < 1030 ) ){
    H=H+1;
  }else{
    H=H;
  }
  TIME=TIME+H*10000;
  M=timeinfo.tm_min;
    TIME=TIME+M*100;
  S=timeinfo.tm_sec;
    TIME=TIME+S;
    
  //split current 4 digit time into sigle digits
  split_time((TIME/100)-((TIME/100)/10000)*10000);
}
//number splitting function to separate time string into digits
void split_time(long long num) {
  first_digit = num / 1000;
  digits[0] = first_digit;
  int first_left = num - (first_digit * 1000);
  second_digit = first_left / 100;
  digits[1] = second_digit;
  //añadimos el segundero fijo (sumamos 10)
  digits[1] = digits[1]+10;
  int second_left = first_left - (second_digit * 100);
  third_digit = second_left / 10;
  digits[2] = third_digit;
  fourth_digit = second_left - (third_digit * 10);
  digits[3] = fourth_digit;
}
// number shifting function
void num_shift(){
  for (dig=0; dig<4; dig++){// turn digits off
    digitalWrite(DigPins[dig], HIGH);
  }
  
  //turn them ON (LOW) one by one
    digitalWrite(DigPins[n], LOW);
    for(int seg=7; seg>=0; seg--){
      //read byte array for digit
      int x = bitRead(ns[digits[n]],seg);
      //turn the segments ON or OFF
      digitalWrite(SegPins[seg],x);
    }
    n++;// move to next no.
    if (n==4){// if no. is 4, restart
      n=0;
    }
}
//Getting room temperature from LM35 sensor via NodeMCU analog input pin (ADC)
void room_temp(){
  readSensors();
  //This will return temperature in XY.Z format
  //We don't want the integer value, so we can use the four digits to display temperature units as well "XYºC"
  //Getting first digit in byte format ns[X] where X=int(XY.Z/10)=int(X.YZ)=X
  digits[0]=int(TEMP/10)-int(TEMP/100)*10;
  //Getting second digit in byte format ns[Y] where Y=int(XY.Z)-X*10=int(XY.Z)-int(XY.Z/10)*10
  digits[1]=int(TEMP/1)-int(TEMP/10)*10;
  //Setting temperature units as degree celsius (ºC) in byte format
  digits[2]=47; //astherisc *
  digits[3]=22; //character C
}
void updateMinutes(){
  //add 1 to the last digit
  digits[3]=digits[3]+1;
  //if greater than 9, reset to 0
  if (digits[3]>9){
    digits[3]=0;
    //then add 1 to the third digit
    updateM0();
  }
  //send last digit to display
  digitalWrite(DigPins[3], LOW);
}
void updateM0(){
  //add 1 to third digit
  digits[2]=digits[2]+1;
  //if greater than 5, reset to 0
  if (digits[2]>5){
    digits[2]=0;
    //then add 1 to current hours
    updateH1();
  }
  //send digit to display
  digitalWrite(DigPins[2], LOW);
}
void updateH1(){
  //add 1 hour
  digits[1]=digits[1]+1;
  // if greater than 19, reset to 10
  // (instead of number 0-9, we use numbers 10-19 in order to add the "dot" to the display)
  if (digits[1]>19){
    digits[1]=10;
    //then add 1 to the first digit
    updateH0();
  }// reset when it's 24h (go back to 00)
  if(digits[1]>13 && digits[0]==2){
    digits[0]=0;
    digits[1]=10;
  }
  //display digits
  digitalWrite(DigPins[1], LOW);
  digitalWrite(DigPins[0], LOW);
}
void updateH0(){
  //add 1 to first digit
  digits[0]=digits[0]+1;
  //if greater than 2, reset to 0 (it shouldn't happen as we reset earlier, but just in case..)
  if (digits[0]>2){
    digits[0]=0;
  }
  //display digit
  digitalWrite(DigPins[0], LOW);
}
void dot_blinker(){
  //every second, blink the dot
    if( millis()-dS > 1000 && dot == 1){
      digits[1]=digits[1]-10;
      dS=millis();
      dot=0;
    }
    if( millis()-dS > 250 && dot == 0){
      digits[1]=digits[1]+10;
      dot=1;
    }
}